Windsor Vinyl Gate

• Before driving your finishing posts, check for underground utilities. In the US, call 811 or visit www.call811.com. In Canada, visit www.clickbeforeyoudig.com to find your provincial one-call centre. This gate needs two finishing posts (BL19109) driven into the ground.
• Read your Windsor Fence Install Guide first so you understand the panel assembly before installing your gate.
• Dry-fit the whole gate frame before driving any permanent screws. It's far easier to troubleshoot fit and assembly order before anything is fastened.
• Install your gate posts before your fence posts — fence panels are more forgiving for a custom fit than a gate.
• Never hang a gate off a single unsupported post. See Hinge Post Support below.

Returns: Please let us help resolve any issues before initiating a return. If a return is still necessary, it must be initiated with the retailer where the product was purchased.

Our US-based customer service team is available Monday-Friday, 9am-5pm EST.

• Parts Website: https://parts.nychbrands.com
• Email: hmmm@wambamfence.com
• Phone: 704-892-5222 or 877-778-5733
• Text: 704-892-5222

For faster service, have your item number (BL19108) and part name ready. A batch lot number (found on the end of the box) is also helpful if available — it helps us identify and resolve any production issues on our end.

Gates do not come with their own posts

You will need two Windsor Finishing Posts — one to finish the fence run, and one to support the gate.

Windsor Fence, Windsor Gate, and Windsor Finishing Post

Drill

Measuring Tape

Pencil

Stringline Reel

Stakes (for stringline)

Large Level

Wrenches

Wood Blocks

Your gate will perform best with complete fence panels on both sides. At minimum, the hinge post should be part of a connected fence run — tying it to a panel that continues to another post lets that post help carry the gate's swinging load, instead of the hinge post bearing it alone. If space restrictions make this impossible, contact us for alternative solutions.

Hinges only open one direction. Decide which way you want your gate to open before mounting your hinges.

A

Gate Bracket (4)

B

Rail (2)
1½in × 3½in × 47¾in

C

Rail Bracket (2)

D

Middle Rail (1)
1½in × 3½in × 40½in

E

Vertical Stiles (2)
1½in × 3½in × 52⅜in

F

Picket (8)
1½in × ⅞in × 55⅞in

G

Hinge (2)

H

Latch Catch (1)

I

Latch Finger (1)

J

1¼in White Self-Drilling Stainless Steel Screw (28)

K

1¼in Black Self-Drilling Stainless Steel Screw (38)

L

Gate Brace with Fasteners (1)

Parts Required

A x2 B x1

Insert the bottom rail (B) fully into one bottom gate bracket (A), then slide the opposite bottom gate bracket (A) onto the other end. Both ends must be seated all the way to the back of their brackets.

Note: Light force may be required to seat the rail fully.

Parts Required

E x2

Insert both vertical stiles (E) into the bottom gate brackets (A). They will bottom out against the bottom rail.

Parts Required

C x2

Mark where your (2) rail brackets (C) will sit on both vertical stiles (E), measuring from the top of the bottom rail to the bottom of each bracket. If you are pairing this gate with the Windsor Fence (BL19107), set the brackets so your middle rails line up for a uniform look.

Important Note Regarding Pool Code: 43½in from the top of the bottom rail to the bottom of the bracket meets typical pool code — always check your local regulations, as requirements vary.

Parts Required

J x4

Fasten both rail brackets (C) at your marked height with (4) white screws (J).

Parts Required

D x1 J x4

Lower the middle rail (D) into both rail brackets (C) and fasten with (4) white screws (J).

Parts Required

F x8

Insert all (8) pickets (F) down through the middle rail and into the bottom rail. Don't be afraid to use muscle — you won't break the vinyl.

Parts Required

A x2 B x1

Insert the top rail (B) fully into one top gate bracket (A), then slide the opposite top gate bracket (A) onto the other end.

Slide the assembled top rail and its gate brackets (A) down over the vertical stiles (E), pressing evenly on both sides until the brackets are fully seated.

Parts Required

J x16

Fasten all (4) gate brackets (A) with (16) white screws (J). Apply pressure at the corners as you drive the screws to keep the frame square.

Parts Required

I x1 G x2 K x14

Fasten the latch finger (I) to the top bracket with (6) black screws (K).

Fasten both hinges (G) to the front of the gate brackets with (8) black screws (K) in total.

Parts Required

L x1

Align the holes and assemble the gate brace (L) using the included hex bolt and washer.

Note: The hardware ships bundled with the gate brace.

Parts Required

J x4

Fasten the gate brace (L) to your gate with (4) white screws (J).

Note: For best performance, install the brace with its top on the same side as the latch finger.

Rest the gate on temporary spacers or wood blocks to hold it at the right height while you install it. Keep the gate's rails level with your fence rails.

Parts Required

G x2 K x6

With the gate still resting on its blocks, fasten the hinges (G) to the hinge post with (6) black screws (K) in total.

Parts Required

K x12

Open the gate and set it on two wood blocks to keep it level. Fasten each hinge (G) with (6) black screws (K) — (4) into the post and (2) into the gate frame.

Note: If your internal pipe anchor sits close to the inside corner of the post, angle your screws to miss it. If the anchor can't be avoided, pre-drill the pipe anchor and install the gate with black 1¼in hex head screws (not included). Do not attempt to drive the pan head screws into the pipe anchor.

Level the gate to the fence post, then check that it swings and latches correctly. Mark where the latch catch needs to go.

Parts Required

H x1 K x6

Align the latch catch (H) to your mark and fasten it with (6) black screws (K).

• Email: hmmm@wambamfence.com
• Phone: 704-892-5222 or 877-778-5733
• Text: 704-892-5222