Edgewood 6ft Privacy Fence

• Before driving pipe anchors, check for underground utilities. In the US, call 811 or visit www.call811.com. In Canada, visit www.clickbeforeyoudig.com to find your provincial one-call centre.
• If installing surface mounted, refer to your Surface Mount install guide (BL19129/BL19130) for specific instructions instead of the steps below.
• If your yard slope exceeds 3–4in per 6ft panel, you will need to split your panel and purchase an extra post and set of brackets.
• This panel does not include posts. See the Posts section below to order your post kits.

Returns: Please let us help resolve any issues before initiating a return. If a return is still necessary, it must be initiated with the retailer where the product was purchased.

Our US-based customer service team is available Monday–Friday, 9am–5pm EST.

• Parts Website: https://parts.nychbrands.com/
• Email: hmmm@wambamfence.com
• Phone: 704-892-5222 or 877-778-5733
• Text: 704-892-5222

For faster service, have your item number (BL19113/BL19114/BL19133) and part name ready. A batch lot number (found on the end of the box) is also helpful if available — it helps us identify and resolve any production issues on our end.

Posts are sold separately — no posts come with this panel

You will need one 6ft H Post (1 pack) or (4 pack) for every post position along your fence run. Unlike other WamBam panels, this panel's box does not include a post/anchor kit — order enough to cover your full run before you begin.

6ft Edgewood Privacy Fence Walnut Brown/Slate Grey/Black, 6ft Edgewood Gate Walnut Brown/Slate Grey/Black, and 6ft Black Aluminum Post 1 pack/4 pack

Important: Check for underground utilities before you start driving your pipes!

In the US, call 811 or visit www.call811.com. In Canada, visit www.clickbeforeyoudig.com to find your provincial one-call centre.

Pounders can be purchased/rented at your local hardware store, or on our website. For safety reasons, we do not recommend using a sledgehammer.

Good

Small Post Pounder 12–18 lbs.
Best for projects with fewer than 10 pipes.

Better

Large Post Pounder 20+ lbs.
Best for 10+ pipes, and may require two people for smoothest operation.

Best

Gas Powered Post Pounder
Rentals are ideal for larger projects. Significantly reduces time and effort required.

Note: Choose a post pounder with a barrel diameter of 3in or greater. Pounder barrel cannot be longer than 24in.

Pounder

Drill Bit

Measuring Tape

Minimum 2in Drill Bit
(included in box)

Hex Bit
(included in box)

Stringline Reel

Stakes (for stringline)

Hammer / Mallet (optional, for stakes)

Pencil

Safety Glasses

Large Level

Small Level

A

Rail Bracket (4)

B

Rail (2)
¾in x 2in x 69¼in

C

Privacy Board (5)
⅝in x 13⅞in x 69in
Boards contain galvanized steel inserts

D

C-Channel (2)
1⅛in x 1¼in x 66⅜in

E

½in Hex Screw (20)
Includes a few extra screws.

F

½in Self-Drilling Screw (6)
Includes a few extra screws

P1

Post Cap (1)

P2

Pipe (1)
2½in x 2½in x 74½in

P3

Post (1)
2½in x 2½in x 75in

Option A

In Ground

Build one full panel first — there is a learning curve. After one panel is installed, it is most efficient to drive all remaining pipes, then build panels onto the posts.

Option B

Surface Mounted

Before you begin, refer to your Surface Mount install guide (BL19129/BL19130) for specific install instructions.

Check your yard's slope before you begin.

If slope is greater than 3–4in per 6ft panel, you will need to split your panel and purchase an extra post and set of brackets.

Place the two stakes for each end of every fence run and tie string between the stakes. Your pipes will be driven according to this line.

Use loose stakes or mark the ground every 72in to determine exact pipe locations, measuring center-to-center.

Parts Required

P2 x1

Warning: Before you install your fence, ensure your donuts are tightened. Do not overtighten.

Parts Required

P2 x1

Drive your pipe into the ground. Check for level roughly every 6in. To help maintain level, pound the pipe equally from all four sides until the lower gear touches the ground. Check that the pipe is level front-to-back and left-to-right. Center of pipe to center of pipe: 72in.

Parts Required

P3 x1

Place your post over your pipe.

Parts Required

A x1 E x2

If your posts are on flat ground, proceed to Step 8.

If your ground is sloped, identify the post that is on higher ground. Secure your bracket as close to the ground as possible against the higher post. Use your rail to ensure the bracket on the lower elevation post is level with the first bracket.

Parts Required

A x1 E x2

Set your bracket within the grooves on your post. Measure 2in from the ground and mark your first post — or stack your two brackets together to mark it instead. Secure the bracket with two ½in hex screws (E) using the included hex bit.

Parts Required

A x1 B x1

Without driving screws, place a rail bracket over the bottom rail. Using a level, mark the location of the second bracket, then remove the rail.

Parts Required

A x1 E x2

Install the bracket to the post at your marked location using two ½in hex screws (E).

Parts Required

B x1 E x4

Secure the bottom rail (B) into both brackets using four ½in hex screws (E).

Note: Ensure the bottom bracket is flush with the rail.

Parts Required

D x2 F x6

Important: Before this step, swap out the hex head drill bit for the Phillips bit included in the bag for part (F). Keep the hex bit close — you'll resume using it shortly.

Align your C-Channel (D) over your bottom bracket. Secure each C-Channel with three ½in self-drilling Phillips screws (F) (six total). The Phillips screws are self-drilling and can drive through aluminum with pressure; a drill bit is also included in the screw bag for part (F).

Parts Required

A x2 E x4

Align your top brackets (A) over your C-Channels and secure with four ½in hex screws (E).

Parts Required

C x5

Install your five boards (C) by sliding them down through the top bracket and C-Channel. Ensure the notch is facing upward. Posts may need to be pushed out slightly at the top to insert the boards.

Parts Required

B x1 E x4

Ensure the rail goes to the back of the bracket. Apply downward force and secure with four ½in hex screws (E).

Parts Required

P1 x1

If needed, trim your posts with a fine-tooth blade, then place post caps (P1) on the posts to finish your panel.

• Email: hmmm@wambamfence.com
• Phone: 704-892-5222 or 877-778-5733
• Text: 704-892-5222